Exactly How to Remove and Change a Tub
Exactly How to Remove and Change a Tub
Blog Article
Everyone maintains their private theory about A Step-by-Step Guide to Installing a Bathtub.
Setting up a bathtub isn't specifically brain surgery, however it does require solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably challenging project. If the old tub is readily accessible, the project can relocate easily; if you need to open up a wall surface to eliminate the old tub and place the brand-new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Make sure you have actually certified on your own for the task and fit trying it. Instead of employing a contractor to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will certainly help you mount a brand-new tub in your bathroom if you have actually already acquired a brand-new tub and also do not need to transform the plan of your previous supply of water pipes.
Your devices as well as product list ought to consist of the following:
Planning for the Installation
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the required position. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub till the level checks out level.
To set up taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub and also examine the overflow electrical outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at the very least when as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Safeguard the faucet in place with the maker offered backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a stiff seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealant can split rather very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that report about Tools You Need to Install a New Bathtub from a good friend on our other web page. Enjoyed our blog entry? Please share it. Help somebody else check it out. I praise you for your time. Visit us again soon.
Book Services
Report this page